Furniture paint process and touch-up skills

furniture production process, in order to extend the service life, and avoid being neatlier scratches, typically to burnish, paint furniture, the furniture paint process? Furniture paint is actually a quite a key working procedure, it directly affects the quality of the furniture already, also affect the appearance of the furniture. Therefore, most of the furniture factory, light is the process to go through a few inspection procedures. Below, we carefully look at the furniture of paint of specific process.

1, furniture sand

sand is a prelude to the paint quality, screening sand quality directly affects the whole product quality problems, is an indispensable process of paint shop. To product inspection before sand on the need for the product test procedure, the texture more deep, have a little missing Angle or local peel place for ash handling, then use flat sanding machine for flat products with 240 # emery paper to grind, some local product cannot use machine operation can use hand or homemade tool grinding. After grinding with 400 # sandpaper to secondary grinding, until to comply with the quality acceptance standard of this process.

2 brush color, furniture

brush color in order to better show the material texture, texture, can appropriate corrective material colour difference, improve the efficiency of repairing color. In the process of the brush color need operators can accurately distinguish different color difference, if there is a big color difference need to color or color, until the color matching. But should pay attention to each product in the process of brush color must be thoroughly put floating color is wiped clean, lest cause color difference between products.

3, furniture bottom oil painting

spraying bottom oil in order to increase the thickness of the furniture paint film, is the purpose of increasing the smoothness of operation of next working procedure. Usually most widely in the furniture industry to fully enclosed, fully enclosed the normal to the bottom of the spraying oil three times, but every time need to grinding of next working procedure. From the deployment of paint to the spray coating quality requirements are very high, generally in the process of operation for the first time is not too thick coating requirement, but the back of the coating are going on with the increase of number of spraying times, each time to achieve uniform coating, cannot appear flowing phenomenon.

4, furniture oil mill

oil mill quality requirement is high, the effect of the oil mill out directly under the influence of several working procedure quality, oil mill is also in the furniture paint problems appeared in the process of making the most of the process.

5, furniture repair color

repairing color to product the biggest role is to make each product's color is consistent, the graphic work products ( Such as mesa, appearance, etc. ) General spray is four times as appropriate. Opposite side should agree with the color of the positive requirements, work products, Such as dining chair, cabinet put oneself in another's position) First the place that it is not easy to for spraying spraying again, the combining site to gun range, cannot appear off color. Each product after spraying operations to compare color plate, color consistent rear can transfer.

6, furniture surface oil painting

a final cleaning surface oil is produced in the process of paint, also is the last procedure in the process of furniture production. Surface oil spraying quality, basically has the following two factors, environmental factors and human factors. Environmental factors refer to spray the room environmental health do not clean enough, leading to paint dry particles is too much, feel is not good. Human factors is refers to the paint spraying uneven, sag, and have not spray part and rough part in place. Is not to say I don't know, the original furniture paint process is so complicated, so much attention to. This also from the other side shows, why we always difficult to DIY paint products meet the relevant requirements, in a sense, strict and complicated process is an important guarantee of quality.

furniture touch-up skills

furniture touch-up mainly for furniture or paint some of the structural damage repair processing. Of furniture for maintenance and surface paint can be divided into structure parts, the processing of color

1, furniture scratch processing: if the furniture to be scratched, but does not touch upon the wood under the paint film, can use soft cloth with a little melted wax liquid, paint coating the wound, cover scars. After being qualitative hard wax, besmear again. So again and again with a few times more, hide them membrane scars.

2, clear water mark, water mark usually would disappear after a period of time. If it is still visible after a month, please use a piece of clean with a small amount of salad oil or mayonnaise soft actually water marks in the wood grain direction is wiped. Or can use wet cloth cover on the print, then press wet cloth electricity iron carefully several times, can be print.

3, remove oil stains from furniture: can add two white vinegar in a water, with sponge wiped mixture oil ink on the wooden door, and then clean and dry it up.

4 yellow, white or light color furniture processing: white or light color paint on the surface of the furniture, time will change color, can use dishcloth touchs toothpaste wipe test.

5, scratch, if furniture paint scratches, not touch wood lacquer, furniture can be used with the same color crayons or in the wound of furniture paint, to cover exposed background, and then use thin transparent nail polish is coated with a layer of can.