Hotel furniture factory production workshop production and the quality specification requirements

hotel furniture factory production workshop requirements adjusted according to actual situation, in products and product quality control by introspection, inspection, process between the transition between department of quality inspection, quality control, test and quality inspection, final inspection control; Self-checking, inspection, process quality inspection, test and the competent in the products department, quality supervision is complete; Department transition by the department in charge of supervision, pay, receive people to complete the quantity, quality confirmation, director's signature.

1, the design requirements according to the order, confirm the material, the size of the various parts of the specifications of the material.

2, have stick wood core board wood texture demand up.

3 before installation, product parts, parts must achieve three fine sand, side panel, door of cupboard of core board with knife, knife to reach level 4 fine sand, feel is smooth with no dent before assembly.

4, on the basis of the component specifications, size combination optimization, improve the utilization rate of material and avoid unplanned under the expected, the cause of the tailings, too much cause the waste of raw materials. )

5, decide according to the flatness, the material thickness, fixed length, such as order, avoid the material deformation effect is too long, cause insufficient thickness or decision not objectively led to an increase in workload.

6, has a complete set of many chest stick wood core board of cupboard door, matching the assembly before you put good texture and color, the same cupboard door has 3 core board, from the bottom up to smooth texture match.

7, multiple combination of cabinet put oneself in another's position for a class of the ark, a single assembly to ensure vertical Angle of 90 degrees, the positive control in 2 - distortion Within 3 mm, exterior size control within 1 mm.

8, width and thickness of more than 55 mm parts, must be split, are not allowed to use natural monolith processing, avoid release or the environmental impact of internal stress of wood stress lead to deformation of the parts.

9, fixed width, or thickness of parts blank, on the basis of design, process and process quality standard into the finishing production.

10, type milling machining parts, according to the size of the turning, the direction of the wood texture, line thickness to determine reasonable feed speed, to ensure that the type milling lines smooth and smooth.

11, parts assembly diagonal controlled within 2 mm, nail head is not exposed to a heavy. For profiled frame assembly to use die fixture to pressure assembly.

12 nail trim, under 10 mm wide should be nailed lines, more than 10 mm above can nail straight nail, nail sink to play in the wood grain direction is not exposed screw head.

13, parts of the tenon, tooth, groove processing, according to the requirement of design reasonable machining allowance and docking site line, surface smooth, mortise butt joint and the overall installation to ensure that the combination is flat and level.

14, mesa, layer board, such as vertical plate plate processing, according to the requirement of design, material quality, texture, selecting reasonable adjusting combination makeup, composite material, to ensure that the split, composite board face texture close to one side or two sides, to avoid affect product overall sensory texture differences.

15, product assembly to see drawings of a complete set of requirements, control the diagonal shape 2 - - Within 3 mm, inside the empty + / - 1 - - Within 2 mm, the size of the shape control in the plus or minus 2 - 5 mm, backplane texture upward, surrounding the steps to uniform. Framework to sanding thicknessing before final assembly.

16, drawer assembly dovetail joint is not allowed to have cracked phenomenon, quadrilateral connecting to flat. Guns played on the plate before and after, not on the two sides, the diagonal tolerance + / - 1 - Good within 2 mm, base plate surface in the department, poor surface at the bottom, bottom peg only play 2 - Four, grain base plate is not loose, but not allowed to play straight nail, triangular piece of reinforcement to apply glue, a drawer use of the same material and color of triangle block, not doping.

17, all parts to should take put down gently, not bruised, with wood veneer board piece to cushion soft goods pile up not scratch in the middle.

18, all the assembly parts, assembly product after completion of the first thing to check, qualified only after installation. Main control points: the overall dimensions, diagonal, the size of the box is empty, cabinet put oneself in another's position, wood vertical upward, nail gong is not exposed, etc.

19, side panel, system frame of the reinforcement or connection, assembly than surface edge bottom 0. 5 - 1mm。

20, drawer assembly before it if there are lack of raw materials, to use putty to fill with color flat sand smooth before assembly.

21, at the bottom of the drawer has two guide rail, to control the space before and after the middle size as parallel, guide groove, such as have deep burr and inverse grain burr to clean before assembly.

22, the assembly after assembly to test whether four feet in one plane, tolerance after the completion of the assembly parts to check within 2 mm, there are cracks, collapse torn needs to fill sand.

23, framework has core board and glass need sets of mold assembly, unilateral joint control in 2 mm, glass tank port to control within 1 mm.

24, all panels connected with thickening box coating glue, directly with gong screw tightening. Assembly assembly glue to clean in time.

25, plate width radian, the annual rings of more than 150 mm and is too large to open expected to split or compound, do not allow the single-layer or single block used, avoid the material deformation of the structure of parts in the natural high risk.

26, sanding machine, sanding, must feed direction and wood grain is consistent, avoid sanding quality problems caused by transverse feeding.

are present in just about every facet of modern life.
If you would like a great tip on where you can get custom furniture custom made furniture for a great price, check out TaoRong Furniture. JiangSu TaoRong Furniture Co., Ltd. is committed to serving globally recognized . Quality is guaranteed here. Make your wise decision.
custom made furniture custom furniture with custom made furniture are used extensively in custom made furniture.
JiangSu TaoRong Furniture Co., Ltd. can promise you that we never conceded on the quality standards of our products.